11/19/2022 0 Comments Pmdg 777 p3d v4![]() ![]() Otherwise my yoke suddenly becomes uncontrollable and go bananas! Frustrating because the sims own controller has an option to define null zones for the brakes which FSUIPC unfortunately don't have (at least to my knowledge).MEET FS2CREW: PMDG 777 EDITION FOR P3D V4 and V5. Unfortunately, as I wrote before, to enable P3Dv4.4s own controls only for the pedals is NOT an option for me - Because I'm not allowed to mix my sims controls with FSUIPC as it is. ![]() The only way I can release brakes here is when turning the Autobrake button off and on several times, otherwise I'm completely stuck in the middle of the runway with ruined tires! When taxing I have to hit the food brake in order to release brakes which I haven't touched in the first place at all! Upon landing, it's not enough to hit the food brake twice (as in the good old FSX days). It will happen mostly during an ILS approach, if I then choose to abort the autolanding and disconnect the autopilot in order to make a visual approach instead, then the yoke will turn all the way to the right and become totally out of control! The only way I can overcome this is by replugging the yoke into the USB slot and from then on it will be controllable again.Īll together, for some reason quite a mess here these days.?!īy disabling P3Dv4.4s own joystick controllers and sending everything through FSUIPC - including the brake on my pedals: "to FS as normal axis" I get an allround perfect and steering setup - EXCEPT for the fact that brakes now seems to block 100% whenever I start taxing and after landing. With this combination I unfortunately still find my yoke going completely bananas and uncontrollable. Which means that my pedals currently is calibrated within the P3D settings environment only, whereas my throutles and yoke is still calibrated inside the FSUIPC environment and send "direct to FSUIPC". Moreover, according to this my previous statement and the following discussion, I've chosen as an experiment to completely keep my pedals out from FSUIPC. From then on my other "joystick", my yoke, went totally bananas and out of control! (During turns on the taxiway I notice that the animated tiller on the PMDG 777-200 actually DO turn - whether this animation is actually a valid reflection of a tiller process taking place for real I can't tell)įor my Saitek pedals ONLY I previously through the years used to send my Axis to "FS as normal axis" (rest of the "joysticks" direct to FSUIPC) which worked fine until FSUIPC/P3Dv4.3. If so, would I actually benefit with such a mix in order to make my front wheel turning more efficient? Is there actually a way to mix the tiller facility with my (physical) pedal rudder axis assignment?Ģ. Please bare over with me, I'm just a regular user and have no skills whatsoever into programming and special FSUIPC mods.ġ. However I'm afraid it got too nerdy for me and didn't really catch the conclusion, if any. I read the " FSLabs A320 Steering/Tiller debate" link which John provided me. I guess, you're right and the problem is still present - probably just me getting more and more use to compensate the lack of turning by using cross throttling. Only the dedicated "direct to FSUIPC calibration" controls are processed differently The exact same controls are sent to the sim. Would it perhaps help if I instead use "Send to FSUIPC Offset" ONLY for my pedals mixed with "send direct to FSUIPC Calibration" for the rest of the "joysticks".?Īssigning in FSUIPC to FS controls is effectively identical to assigning in P3D. From then on my other "joystick", my yoke, went totally bananas and out of control! No surprise here, as according to the manual, one is not supposed to mix "send direct to FSUIPC Calibration" and "FS as normal axis".anyway this worked for a long time, until now when I don't seem to have no other choice than let all my axis on all my "joysticks" assign to "send direct to FSUIPC Calibration", which in practise wont work for my pedals! Can't seem to configure my Saitek pedals correct through "send direct to FSUIPC Calibration" along with PMDG 777.īrakes and rudder works fine, but the front wheel works poorly, which means that I have to use my throttles violently as a compensation in order to make sharp turns.įor my Saitek pedals ONLY I previously through the years used to send my Axis to "FS as normal axis" (rest of the "joysticks" direct to FSUIPC) which worked fine until FSUIPC/P3Dv4.3. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |